Question 1

Which term refers to electronic assembly drawings that contain details needed to make or trace all electronic connections?

Accepted Answer

A)   wiring diagram
B)   block diagram
C)   logic diagram
D)   chassis drawingE) C) and D)
F) None of the above

Question 2

When drawing a logic diagram, logic symbols should be:

Accepted Answer

A)   drawn with input and output letters inside of them
B)   evenly spaced
C)   positioned vertically
D)   placed on a separate pageE) None of the above
F) A) and B)

Question 3

The American Standards Association (ASA) is one of the organizations that oversees the standardization of electronics and electrical drawings.

Accepted Answer

A) True 
 B)False

Question 4

Connection diagrams are supplementary drawings used with a block diagram for installing and repairing electronic equipment.

Accepted Answer

A) True 
 B)False

Question 5

When drawing a connection diagram, it is common to draw the wires with corner radii and color labels.

Accepted Answer

A) True 
 B)False

Question 6

What is the reference designation for a potentiometer?

Accepted Answer

A)   R
B)   C
C)   P/J
D)   QE) None of the above
F) B) and C) A

Question 7

A _____ is a general presentation drawing used to simplify and show the interrelationship of the various parts of an entire electronics system.

Accepted Answer

A)   pictorial drawing
B)   schematic diagram
C)   multiview drawing
D)   block diagramE) A) and C)
F) B) and C)

Question 8

When preparing a schematic diagram, you should:

Accepted Answer

A)   place symbols and connectors as close as possible
B)   keep the crossing of connector lines to a minimum
C)   place reference callouts on a separate page
D)   never use a grid overlay if scale is a factorE) A) and D)
F) A) and C)

Question 9

In a block diagram, the differently-shaped blocks are joined by a double line with arrows.

Accepted Answer

A) True 
 B)False

Question 10

When drawing a logic diagram, the connecting lines should be drawn _____ the symbol lines.

Accepted Answer

A)   thinner
B)   thicker
C)   perpendicular to
D)   parallel toE) None of the above
F) A) and D)

Question 11

A _____ serves as the master reference for the preparation of production drawings, parts lists, and component specifications.

Accepted Answer

A)   block diagram
B)   schematic diagram
C)   pictorial drawing
D)   multiview drawingE) B) and C)
F) All of the above

Question 12

When preparing electronics drawings, you should:

Accepted Answer

A)   lay out circuits so that they read from right to left
B)   always use the same scale for different and discrete parts of a diagram
C)   avoid line crossovers whenever possible
D)   use angular lines wherever possibleE) A) and C)
F) A) and D)

Question 13

According to EIA color code standards, wire number 2 in a trunkline diagram should be:

Accepted Answer

A)   orange
B)   white
C)   black
D)   redE) B) and D)
F) A) and B) D

Question 14

Complex circuits should be read from the lower left to the upper right.

Accepted Answer

A) True 
 B)False

Question 15

Imagine that you see a dash (-)  on a schematic diagram. What does it refer to?

Accepted Answer

A)   connector
B)   ground
C)   transistor
D)   inverterE) All of the above
F) B) and D)

Question 16

A printed circuit board electrically connects components through printed _____ conductors on an insulated board.

Accepted Answer

A)   steel-infused ink
B)   brass
C)   lead
D)   copperE) None of the above
F) A) and B)

Question 17

Automotive manuals frequently contain point-to-point diagrams for troubleshooting purposes.

Accepted Answer

A) True 
 B)False  True

Question 18

In industry, electronic drawings may be simple or very complex.

Accepted Answer

A) True 
 B)False

Question 19

If you need to design the microcircuitry used in a computer, you should draw a _____ diagram.

Accepted Answer

A)   point-to-point
B)   baseline
C)   logic
D)   cableformE) None of the above
F) B) and C)

Question 20

Which statement about printed circuit drawings is correct?

Accepted Answer

A)   They enable complex circuits to be miniaturized.
B)   They are prepared at a very small scale.
C)   They are more expensive to produce than wired circuits.
D)   Only a single drawing is needed to design and create the documentation necessary to produce a printed circuit board.E) A) and C)
F) None of the above

Exam 22: Electronics Drafting

Which term refers to electronic assembly drawings that contain details needed to make or trace all electronic connections?

Correct AnswerverifiedShow Answer

When drawing a logic diagram, logic symbols should be:

Correct AnswerverifiedShow Answer

The American Standards Association (ASA) is one of the organizations that oversees the standardization of electronics and electrical drawings.

Correct AnswerverifiedShow Answer

Connection diagrams are supplementary drawings used with a block diagram for installing and repairing electronic equipment.

Correct AnswerverifiedShow Answer

When drawing a connection diagram, it is common to draw the wires with corner radii and color labels.

Correct AnswerverifiedShow Answer

What is the reference designation for a potentiometer?

Correct AnswerverifiedA

A _____ is a general presentation drawing used to simplify and show the interrelationship of the various parts of an entire electronics system.

Correct AnswerverifiedShow Answer

When preparing a schematic diagram, you should:

Correct AnswerverifiedShow Answer

In a block diagram, the differently-shaped blocks are joined by a double line with arrows.

Correct AnswerverifiedShow Answer

When drawing a logic diagram, the connecting lines should be drawn _____ the symbol lines.

Correct AnswerverifiedShow Answer

A _____ serves as the master reference for the preparation of production drawings, parts lists, and component specifications.

Correct AnswerverifiedShow Answer

When preparing electronics drawings, you should:

Correct AnswerverifiedShow Answer

According to EIA color code standards, wire number 2 in a trunkline diagram should be:

Correct AnswerverifiedD

Complex circuits should be read from the lower left to the upper right.

Correct AnswerverifiedShow Answer

Imagine that you see a dash (-) on a schematic diagram. What does it refer to?

Correct AnswerverifiedShow Answer

A printed circuit board electrically connects components through printed _____ conductors on an insulated board.

Correct AnswerverifiedShow Answer

Automotive manuals frequently contain point-to-point diagrams for troubleshooting purposes.

Correct AnswerverifiedTrue

In industry, electronic drawings may be simple or very complex.

Correct AnswerverifiedShow Answer

If you need to design the microcircuitry used in a computer, you should draw a _____ diagram.

Correct AnswerverifiedShow Answer

Which statement about printed circuit drawings is correct?

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
A

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
D

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
True

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified